20ft (6 m) of 3/4-inch copper coil 6 feet of heat-proof silicone tubing A two-gallon bucket Tea kettle or pressure cooker Ice Sealer A large water bottle to collect the distilled water
If you are using a two-gallon bucket, be sure that there is a 3/4-inch hole at the top of the bucket and the bottom of the bucket. The copper tubing will need to be fed through both holes in order to collect the steam (at the top) and emit the water (at the bottom).
Simply place your coiled copper tubing inside the bucket or jug, leaving a 1-inch gap in between the tubing and the sides of the bucket. Remember to feed the top and bottom of the copper coil through the holes you’ve drilled in the bucket. If the tube seems too loose, you can use epoxy or sealant to ensure that the tubing fits snugly in the holes. [2] X Research source {“smallUrl”:“https://www. wikihow. com/images/thumb/8/84/Make-a-Water-Still-Step-4Bullet1. jpg/v4-460px-Make-a-Water-Still-Step-4Bullet1. jpg”,“bigUrl”:"/images/thumb/8/84/Make-a-Water-Still-Step-4Bullet1. jpg/aid67718-v4-728px-Make-a-Water-Still-Step-4Bullet1. jpg",“smallWidth”:460,“smallHeight”:345,“bigWidth”:728,“bigHeight”:546,“licensing”:"<div class="mw-parser-output">
License: <a target="_blank" rel="nofollow noreferrer noopener" class="external text" href="https://creativecommons.
org/licenses/by-nc-sa/3.
0/">Creative Commons</a>
\n</p>
<br />\n</p></div>"}
If the pressure valve on the pressure cooker is too small, you can use a brass fitting of the same diameter as the tube to allow the silicone tubing to fit tightly. {“smallUrl”:“https://www. wikihow. com/images/thumb/f/f5/Make-a-Water-Still-Step-5Bullet1. jpg/v4-460px-Make-a-Water-Still-Step-5Bullet1. jpg”,“bigUrl”:"/images/thumb/f/f5/Make-a-Water-Still-Step-5Bullet1. jpg/aid67718-v4-728px-Make-a-Water-Still-Step-5Bullet1. jpg",“smallWidth”:460,“smallHeight”:345,“bigWidth”:728,“bigHeight”:546,“licensing”:"<div class="mw-parser-output">
License: <a target="_blank" rel="nofollow noreferrer noopener" class="external text" href="https://creativecommons.
org/licenses/by-nc-sa/3.
0/">Creative Commons</a>
\n</p>
<br />\n</p></div>"} If the spout on your tea kettle is too large, simply drill a hole in a rubber stopper that is the same diameter as your tubing. Place this stopper in the kettle spout and insert your tubing. {“smallUrl”:“https://www. wikihow. com/images/thumb/7/7c/Make-a-Water-Still-Step-5Bullet2. jpg/v4-460px-Make-a-Water-Still-Step-5Bullet2. jpg”,“bigUrl”:"/images/thumb/7/7c/Make-a-Water-Still-Step-5Bullet2. jpg/aid67718-v4-728px-Make-a-Water-Still-Step-5Bullet2. jpg",“smallWidth”:460,“smallHeight”:345,“bigWidth”:728,“bigHeight”:546,“licensing”:"<div class="mw-parser-output">
License: <a target="_blank" rel="nofollow noreferrer noopener" class="external text" href="https://creativecommons.
org/licenses/by-nc-sa/3.
0/">Creative Commons</a>
\n</p>
<br />\n</p></div>"}
Plywood (4 feet by 8 feet) One sheet of high-finish, tempered glass (27. 25 x 22 inches) Wood glue High-temperature black paint Screws Drill with drill bits Caulk PEX tubing (2 feet) Rigid insulation Two long, flat glass baking pans
A bottom base that measures 23. 25 x 19 inches A short end piece that measures 5. 75 x 20. 5 inches A long end piece that measures 9 x 20. 5 inches Two trapezoidal side pieces that measure 9 1/8 inches tall (at the long end), 5 1/8 inches tall (at the short end), and 26. 75 inches wide Note that a circular saw set to a 9 degree angle can help you cut the trapezoidal pieces correctly[4] X Research source
Use caulk or sealant to make sure that the piping fits snugly in the hole you drilled and that the open tubing is securely fastened to the plywood. [11] X Research source {“smallUrl”:“https://www. wikihow. com/images/thumb/c/cf/Make-a-Water-Still-Step-16Bullet1. jpg/v4-460px-Make-a-Water-Still-Step-16Bullet1. jpg”,“bigUrl”:"/images/thumb/c/cf/Make-a-Water-Still-Step-16Bullet1. jpg/aid67718-v4-728px-Make-a-Water-Still-Step-16Bullet1. jpg",“smallWidth”:460,“smallHeight”:345,“bigWidth”:728,“bigHeight”:546,“licensing”:"<div class="mw-parser-output">
License: <a target="_blank" rel="nofollow noreferrer noopener" class="external text" href="https://creativecommons.
org/licenses/by-nc-sa/3.
0/">Creative Commons</a>
\n</p>
<br />\n</p></div>"}
You can use a temporary stop or painters tape to secure the caulked glass roof until it has dried thoroughly. [13] X Research source
