A power hand drill is one of the easiest ways to cut a hole into the coconut, but if you do not have one, you could also use a corkscrew, screwdriver, or metallic skewer, instead. Worst case scenario, you can use a hammer and a nail. Pound the nail into the coconut using the hammer. Then, using the back end of the hammer to lift the nail back out, creating a hole. Create your hole in one of the three “eyes” of the coconut. These spots are the thinnest spot on the outer shell and the easiest to drill through. It may help to hold the coconut on a non-slip surface, like a cutting board or kitchen towel, to prevent it from slipping around as you attempt to drill through it.
Coconut water can be used for cooking purposes or served with ice as a beverage, but if you have no plans for the coconut water, simply discard it by pouring the water down the drain. [3] X Research source
For best results, place the coconut on a cement floor, sidewalk, or other equally hard surface. Do not use a kitchen counter since you may accidentally damage the counter as you strike the coconut. Use as much force as possible to strike the coconut in the direct middle. Some will open quickly, while others may take more effort. You could also open the coconut by striking its center on a sharp rock or by sawing it in half with a hand saw. If using a saw, saw down the center seam that passes in between the eyes of the coconut.
Cut through the meat by making a cut from the inside all the way through to the shell. Use your fingers or the tip of the knife to pry the meat off the shell in chunks. To make the process easier, cut the meat into v-shaped sections or cross-hatched sections, creating pieces inside the shell that can be readily removed. [6] X Research source You might be able to wedge a metal spoon or dull knife in between the meat and the shell without making any slices through the center of the meat. If you can, try lifting the meat away from the shell after wedging the utensil in the gap.
If you successfully removed all of the flesh from the shell, there will be a brown skin on the portion of the flesh that touched the shell. This part needs to be removed before you can prepare the coconut for flour or any other use.
If desired, you could use a food processor instead of a blender. Make sure that the food processor is large enough to hold both the coconut and the water you will be adding to it, however.
The water should completely cover the coconut. Strictly speaking, the water does not need to be boiling, but boiling water will soak into the coconut quicker than cool or room temperature water. To accomplish the same level of absorption using cool or room temperature water, let the coconut meat soak in the water for 2 hours before pressing forward.
The pulp will not be “puree” smooth, but there should be no large chunks of coconut remaining or any soupy areas. The water and coconut should be evenly blended and dispersed throughout.
If you do not give the pulp time to rest, you may burn your fingers when you try to strain it. Note, however, that this is not an issue if you used cool or room temperature water. In that instance, the pulp can be strained immediately.
If you do not have a nut milk bag, you could use a cheesecloth. Arrange the cheesecloth into a mesh strainer and pour the contents of the blender through the cheesecloth and strainer. As before, collect the milk in a bowl placed beneath the bag and use the pulp for your flour. You will not need the coconut milk any longer for this particular project. The coconut milk can be discarded, if desired, but you can also drink the milk or use it for cooking purposes as a substitution for dairy milk.
The oven needs to be set to a very low temperature. The objective is to dehydrate the coconut pulp without toasting or burning it. The only way to do this in your oven is to bake the coconut at as low a temperature as possible. Do not use cooking spray. The surface of the cookie sheet needs to be dry. Do not use aluminum foil. The delicate coconut taste can be affected by the metallic taste of foil.
Use a fork to break up any large chunks of pulp. The layer of coconut should be as thin as possible.
After pulling it out of the oven, let it cool off for 1 or 2 minutes. Carefully touch it with your hands. If it feels perfectly dry, the coconut is ready. If you can still feel some moisture, you should put it back into the oven for a few more minutes. Coconut can burn even at low temperatures, so you need to monitor the coconut closely as it dehydrates. Pull it out of the oven at the first sign of toasting or burning.
Do not add any water or other ingredients. It is crucial that the coconut be completely dry as it goes into the food processor or blender. Make sure that the food processor or blender is completely dry, as well. If you are using the same blender used during the coconut milk part of the process, you will need to wipe the bucket dry using paper towels before you can add the dry, dehydrated pulp back into it.
You may need to use a dry spatula to stir the coconut flour so that all the pieces are exposed to the blades and thoroughly ground up. If you do this, however, pause the pulsing or blending process whenever you put the spatula into the machine.
When stored properly, coconut flour can last up to one year on the shelf. That said, fresh coconut flour usually tastes better than old coconut flour.
